Honeywell VisionPRO TH8000 Series Programmable Thermostats Installation Manual

Honeywell

Honeywell VisionPRO TH8000 Series Programmable Thermostats

Honeywell VisionPRO TH8000 Series Programmable Thermostats

About Honeywell

We hold approximately 3,000 active and pending patents worldwide for our Honeywell Home products, and we continue to create dependable technology crafted for your comfort.

Our connected technology is based on 130 years of experience and the proven expertise of the Honeywell Home brand, a brand Resideo continues to offer today.

Information

This manual covers the following models

  • TH8110U: For 1 Heat/1 Cool systems
  • TH8320U: For up to 3 Heat/2 Cool systems
  • TH8321U: For up to 3 Heat/2 Cool systems with dehumidification
    (Pull thermostat from wallplate and turn over to find model number)

System Types

  • Gas, oil, or electric heat with air conditioning
  • Warm air, hot water, high-efficiency furnaces, heat pumps, steam, gravity
  • Heat only — two-wire systems, power to open and close zone valves (Series 20), and normally open zone valves
  • Heat only with a fan
  • Cool only
  • 750 mV heating systems

This thermostat contains a Lithium battery which may contain Perchlorate material. Perchlorate Material—special handling may apply, See www.dtsc.ca.gov/hazardouswaste/perchlorate

Need Help?

For assistance with this product please visit http://customer.honeywell.com or call Honeywell Customer Care toll-free at 1-800-468-1502

Wallplate installation

Honeywell VisionPRO TH8000 Series Programmable Thermostats Installation Manual (1)

  1. Separate wallplate from thermostat.
  2. Mount the wallplate as shown below.

Must be installed by a trained, experienced technician

  • Read these instructions carefully. Failure to follow these instructions can damage the product or cause a hazardous condition.

MERCURY NOTICE

If this product is replacing a control that contains mercury in a sealed tube, do not place the old control in the trash. Contact your local waste management authority for instructions regarding recycling and proper disposal.

CAUTION: ELECTRICAL HAZARD

Can cause electrical shock or equipment damage. Disconnect power before beginning installation.

Power options

Honeywell VisionPRO TH8000 Series Programmable Thermostats Installation Manual (2)

Wiring

Honeywell VisionPRO TH8000 Series Programmable Thermostats Installation Manual (3)

Terminal Designations

Shaded areas below apply only to TH8320/TH8321.

Conventional Terminal Letters:  

  • R Heating power. Connect to the secondary side of the heating system transformer.
  • RC Cooling power. Connect to the secondary side of the cooling system transformer.
  • C Common wire from the secondary side of the cooling transformer (if 2 transformers). 1st stage heat relay. W W2 2nd stage heat relay.
  • Y 1st stage compressor contactor.
  • Y2 2nd stage compressor contactor.
  • G Fan relay.
  • S1 Optional outdoor or remote sensor.
  • S2 Optional outdoor or remote sensor.

Heat Pump Terminal Letters:  

R Heating power. Connect to the secondary
side of the heating system transformer.
Cooling power. Connect to the secondary
side of the cooling system transformer.
The common wire is from the secondary side of
the cooling system transformer.
1st stage compressor contactor.
Rc
C
Y
Y2 2nd stage compressor contactor.
Aux/E Auxiliary/Emergency heat relay.
G Fan relay.
L Heat pump reset (powered continuously
when System is set to Em Heat; system
monitor when set to Heat, Cool or Off).
O/B Changeover valve for heat pumps.
S1 Optional outdoor or remote sensor.
S2 Optional outdoor or remote sensor.

Wiring guide—conventional systems

Shaded areas below apply only to TH8320/TH8321.

Honeywell VisionPRO TH8000 Series Programmable Thermostats Installation Manual (4)

See [ notes ] below

  1. Power supply. Provide disconnect means and overload protection as required.
  2. Remove jumper for 2-transformer systems.
  3. Optional 24VAC common connection.
  4. The common connection must come from the cooling transformer.

Honeywell VisionPRO TH8000 Series Programmable Thermostats Installation Manual (5)

See [ notes ] below

  1. Power supply. Provide disconnect means and overload protection as required.
  2. Optional 24VAC common connection.
  3. O/B is set to control as either O or B in the installer setup.
  4. If the L terminal is used, 24VAC common (terminal C) must be connected.
  5. Heat pump reset (powered continuously when the thermostat is set to Em. Heat; system monitor when set to Heat, Cool, or Off).

Remove the tab and mount the thermostat

Honeywell VisionPRO TH8000 Series Programmable Thermostats Installation Manual (6)

Align pins on the back of the thermostat with slots in the wallplate, then push gently until the thermostat snaps into place.

Set date and time

Honeywell VisionPRO TH8000 Series Programmable Thermostats Installation Manual (7)

Installer setup

Honeywell VisionPRO TH8000 Series Programmable Thermostats Installation Manual (8)

Honeywell VisionPRO TH8000 Series Programmable Thermostats Installation Manual (9)

Honeywell VisionPRO TH8000 Series Programmable Thermostats Installation Manual (10)

0120 Year
(first two digits)
20 ( 20 01- 20 99)
21 ( 21 00- 21 78)
0130 Year
(second two digits)
12 (20 12 )
[Other options: 00-99]
0140 Month 6 [Other options: 1-12]
0150 Date 15 [Other options: 1-31]
0160 Schedule format 4 7-day programming
0 Non-programmable
0170 System type 1 1 heat/1 cool conventional
2 1 heat/1 cool heat pump (no aux. heat)
3 Heat-only (2-wire systems)
4 Heat only with fan
5 Hot water Series 20 system (power to open & close zone
valves/normally open zone valves)
6 Cool only
7 2 heat/1 cool heat pump (with aux. heat)
8 2 heat/2 cool multistage conventional
9 2 heat/1 cool multistage conventional
10 1 heat/2 cool multistage conventional
11 2 heat/2 cool heat pump (no aux. heat)
12 3 heat/2 cool heat pump (with aux. heat)
0180 Fan control
(heating)
0 Gas/Oil heat (equipment controls the heating fan)
1 Electric furnace (thermostat controls the heating fan)
0190 Changeover valve
(O/B terminal)
0 O/B terminal controls valve in cooling
1 O/B terminal controls valve in heating
0200 Auxiliary heat 0 Electric backup heat
1 Fossil fuel backup heat
0210 External fossil
fuel kit
1 External fossil fuel kit controls backup heat
0 Thermostat controls backup heat (outdoor sensor required)
0220 1st stage com
pressor cycle rate
3 Recommended for most compressors
[Other options: 1, 2, 4, 5, or 6 CPH]
0230 2nd stage com
pressor cycle rate
3 Recommended for most compressors
[Other options: 1, 2, 4, 5, or 6 CPH]
0240 First stage heat
cycle rate (CPH=
cycles per hour)
5 Gas or oil furnaces of less than 90% efficiency
1 Steam or gravity systems
3 Hot water systems & furnaces of 90%+ efficiency
9 Electric furnaces
[Other options: 2, 4, 6, 7, 8, 10, 11, 12 CPH]
0250 Second stage heat
cycle rate (CPH)
5 Gas or oil furnaces of less than 90% efficiency
1 Steam or gravity systems
3 Hot water systems & furnaces of 90%+ efficiency
9 Electric furnaces
[Other options: 2, 4, 6, 7, 8, 10, 11, 12 CPH]
0260 Third stage heat
cycle rate (CPH)
9 Electric auxiliary heat or electric furnaces
1 Steam or gravity systems
3 Hot water systems & furnaces of 90%+ efficiency
5 Gas or oil furnaces of less than 90% efficiency
[Other options: 2, 4, 6, 7, 8, 10, 11, 12 CPH]
0280 Backlight 0 Backlight on for approx. 8 seconds after the keypress
1 Backlight always on low intensity, full bright after key
press (requires 24VAC connection)
0300 Manual/Auto
changeover
0 Manual changeover (Heat/Cool/Off)
1 Automatic changeover (Heat/Cool/Auto/Off)
0310 Auto changeover
deadband
3 Heat/cool temperature 3°F apart (1.5°C) ** See page 11
[Other options: 2-9 (2°F to 9°F/1.5 °C to 5°C)]
0320 Temperature
display
0 Fahrenheit
1 Celsius
0330 Daylight savings 2 Auto-change to daylight savings time (2007 and be
yond, for areas that use the new 2007 DST calendar)
1 Auto-change to daylight savings time (through 2006, and
for areas that do not use the new 2007 DST calendar)
0 Daylight savings time is turned off
0340 Remote sensor 0 No remote sensor
1 Outdoor sensor (display only)
2 Outdoor control sensor (select heat pumps) ** See page 11
3 Indoor sensor
0350 Heat pump
compressor lockout
0 No heat pump compressor lockout
[Other options: 15, 20, 25, 30, 35, 40°F (-9.5°C to 7°C)]
0360 Heat pump 0 No heat pump auxiliary lockout
0500 Furnace filter
change reminder
0 Off
1 10-day run time (about 1 month)
2 30-day run time (about 3 months)
3 60-day run time (about 6 months)
4 90-day run time (about 9 months)
5 120-day run time (about 1 year)
6 365-day run time (about 3 years)
0510 Humidifier pad
change reminder
0 Off
1 90 calendar days
2 180 calendar days
3 365 calendar days
0520 UV lamp change
reminder
0 Off
1 365 calendar days
0530 Adaptive Intelligent
Recovery™
1 On ** See page 11
0 Off
0540 Program periods 4 4 program periods (Wake, Leave, Return, Sleep)
2 2 program periods (Wake, Sleep)
0580 Compressor
protection
5 5 minute compressor off time ** See page 11
[Other options: 0, 1, 2, 3, or 4-minute off time]
0600 Heat temperature
range stop
90 Max. heat temperature setting is 90°F (32°C)
[Other options: 40-89°F (4.5°C to 32°C)]
0610 Cool temperature
range stop
50 Min. cool temperature setting is 50°F (10°C)
[Other options: 51-99°F (10.5°C to 37°C)]
0640 Clock format 12 12-hour time (i.e., “3:30 pm”)
24 24-hour time (i.e., “15:30”)
0650 Extended fan
timer (heat)
0 Off
90 Fan runs for 90 seconds after the call for heat ends
0660 Extended fan
timer (cool)
0 Off
90 Fan runs for 90 seconds after the call for cooling ends
0670 Keypad lock 0 Keypad unlocked (fully functional)
1 Partially locked (access to temperature settings only)
2 Fully locked
0680 Heat temperature
control
2 Standard temperature control (recommended)
1 Choose if the room is warmer than the set temperature
3 Choose if the room does not reach the set temperature
0690 Cool temperature
control
2 Standard temperature control (recommended)
1 Choose if the room is cooler than the set temperature
3 Choose if the room does not reach the set temperature
0700 Temperature
display offset
0 Thermostat displays actual room temperature
[Other options: -3, -2, -1, 1, 2, 3°F offset (-1.5°C to 1.5°C)
0710 RESET 0 No reset
1 Reset installer options & program schedule to factory
default (only date and time settings are retained)

Installer system test

Honeywell VisionPRO TH8000 Series Programmable Thermostats FIG-11

System test System status
1 Cooling system 0 Compressor and fan turn off
1 Compressor and fan turn on
2 Second stage compressor turns on
2 Fan system 0 Fan turns off
1 Fan turns on
3 Heating system 0 Heat and fan turn off
1 Heat turns on (fan on if Function 0170 is set for heat pump,
or if Function 0180 is set to “1”) ** See page 6
2 Second stage heat turns on
3 Third stage heat turns on
4 Emergency
heating system
0 Heat and fan turn off
1 Heat and fan turn on

CAUTION: EQUIPMENT DAMAGE HAZARD. Compressor protection is bypassed during testing. To prevent equipment damage, avoid cycling the compressor quickly.

Special functions

Auto Changeover (Setup Function 0300):

When set to Auto, the thermostat automatically selects heating or cooling depending on the indoor temperature. Heat and cool settings must be at least 2 degrees apart. If function 0380 is set to On, the heat and cool settings must be at least 5 degrees apart.

Remote Sensor (Setup Function 0340):

If an optional outdoor sensor is installed, the thermostat can display the outside temperature. If an optional remote indoor sensor is installed, the thermostat will display the temperature at the sensor location (the internal sensor in the thermostat is not used).

Adaptive Intelligent Recovery (Setup Function 0530):

Allows the thermostat to “learn” how long the furnace and air conditioner take to reach programmed temperature settings, so the temperature is reached at the scheduled time.

Compressor Protection (Setup Function 0580): Forces the compressor to wait a few minutes before restarting, to prevent damage. During this time, the message “Wait” flashes on the display. Dehumidification control (Setup Function 0380): TH8321 models monitor the indoor humidity level and automatically activate the cooling system to reduce humidity by lowering the temperature by up to 3 degrees below the current cool setting.

Heat Pump Temperature Lockout (with fossil fuel backup):

If the thermostat is installed with an optional outdoor sensor, you can select a compressor lockout temperature (Function 0350). When the outdoor temperature is below the lockout temperature, only the auxiliary heat operates. When the outdoor temperature is above the lockout temperature, only the compressor operates.

Heat Pump Temperature Lockouts (with electric heat backup):

If the thermostat is installed with an optional outdoor sensor, you can select a compressor lockout temperature (Function 0350) and/ or an auxiliary heat lockout temperature (Function 0360).

When the outdoor temperature is below the compressor lockout temperature, only the auxiliary heat operates. When the outdoor temperature is above the auxiliary lockout temperature, only the compressor operates.

If the outdoor temperature is between the compressor and auxiliary lockout temperatures, both the compressor and auxiliary heat can operate.

Accessories & replacement parts

Please contact your distributor to order replacement parts.

  • Outdoor temperature sensor ………………………… Part Number C7089U1006
  • Remote indoor temperature sensor ……………… Part Number C7189U1005
  • Cover plate* …………………………………………………… Part Number 32003796-001
    *(Use to cover marks left by old thermostats.)

Specifications

  • Temperature Ranges

    • Heat: 40° to 90°F (4.5° to 32°C)
    • Cool: 50° to 99°F (10° to 37°C)
  • Operating Ambient Temperature
    • 0° to 120°F (-18° to 48.9°C)
  • Shipping Temperature
    • -30° to 150°F (-34° to 66°C)
  • Operating Relative Humidity
    • 5% to 90% (non-condensing)
  • Physical Dimensions
    • 4-9/16” H x 6” W x 1-3/8” D
    • 116 mm H x 152 mm W x 35 mm D

Electrical Ratings

Honeywell VisionPRO TH8000 Series Programmable Thermostats FIG-12

Honeywell International Inc.
1985 Douglas Drive North
Golden Valley, MN 55422
http://customer.honeywell.com
Automation and Control Solutions

U.S. Registered Trademark.
© 2012 Honeywell International Inc.
69-2693—01 M.S. 01-12
Printed in the U.S.A

FAQs About Honeywell VisionPRO TH8000 Series Programmable Thermostats

Is there a battery in the Honeywell VisionPRO 8000?

Batteries: Three AAA alkaline batteries that can be replaced: When the 24-volt common is not used, power thermostats.

How do I program my Honeywell thermostat?

Setting the temperature on your Honeywell thermostat is simple if you have a manual thermostat. To adjust the temperature, simply press the up and down buttons. The temperature you set will remain until you change it again.

What happens if the Honeywell thermostat battery runs out?

A dead set of batteries renders your programmable thermostat inoperable, preventing you from controlling your HVAC system. You’ll also lose the pre-programmed settings on your thermostat. You’ll have no choice but to change the batteries if you get this far.

Is the Honeywell 8000 capable of controlling humidity?

To control humidification, dehumidification, or ventilation, use the VisionPRO 8000 thermostat, wall anchors, screws, and universal IAQ contacts.

What is the definition of Honeywell thermostat cycles per hour?

A cycle rate is the number of times a system will run in an hour at 50% capacity to maintain a given temperature. A cycle rate of 3 is recommended for high-efficiency (90%+) gas or oil-forced air systems. This means that the heating system will cycle no more than three times per hour.

What apps are compatible with Honeywell thermostats?

Users can use the Honeywell Total Connect Comfort app to remotely monitor and manage their heating and cooling systems at any time and from any location.

How do I change the setting on my Honeywell thermostat to automatic?

When it says “auto cool,” you must first press the mode button until the mode changes to “heat,” then use the + or – to change the heat set-point. Then, press the mode button to return to Auto Changeover mode.

How do you set a Honeywell thermostat manually?

Switch between fan-only, cooling, and heating modes by using the thermostat’s buttons. The temperature can be adjusted using the up and down arrow buttons. To save energy, program or schedule thermostats to work less while you’re away from home. Specific setting instructions can be found in your user manual.

How do I change the temperature on my VisionPro thermostat?

Replace the Thermostat Installing the battery backward for five seconds, pushing a recessed reset button with a pin or paper clip, or turning off the thermostat’s breaker for 30 seconds are all common methods for resetting a thermostat.

For More Manuals by Honeywell, Visit the Latest Manual

Honeywell VisionPRO TH8000 Series Programmable Thermostats Installation Manual [pdf]

Leave a Reply